|
Outside Corner End |
|
 |
 |
|
(H-OCE) is used at the
ends of fingers, ends of dock, or for a swim
platform.
$14.19 |
|
Outside Corner Male |
|
 |
 |
|
(H-OCM) has one 1/2"
tab and a hole for a 3/4" bolt or pin. Use
with an Outside Corner Female (H-OCF) or with a
Single "T" Female (H-SF).
$20.47 |
|
Outside Corner Female |
|
 |
 |
|
(H-OCF) has two 1/2"
tabs and a hole for a 3/4" bolt or pin.
Use with an Outside Corner Male (H-OCM) or with
a Single "T" Male (H-SM).
$24.51 |
|
Inside Corner |
|
 |
 |
|
(H-IC) has slots and
can be used with 1 1/2" - 3" thick wood.
The inside corner sandwiches the wood between
the opposite outside corner, keeping bolts from
burying themselves in the wood. A corner
gusset gives the unit a lot of strength and
helps from racking the dock.
$15.12 |
|
Single "T" Male |
|
 |
 |
| (H-SM)
has one 1/2" tab and is used with an Outside
Corner Female (H-OCF) or Single "T" Female.
$10.98 |
|
Single "T" Female |
|
 |
 |
| (H-SF)
has two 1/2" tabs and is used with an Outside
Corner Male (H-OCM) or a Single "T" Male (H-SM).
Both male and female singles can be bolted to
the side of a dock to make finger attachments.
They can also be bolted to seawalls to make
ramps. $15.37 |
|
Washer Plates |
|
 |
 |
| (H-W) are
used mostly with Angles (H-A) and Cleat Angles
(H-CA). The square hole in the plate keeps
the carriage bolts from turning when the bolts
are tightened.
$1.49 |
|
Angles |
|
 |
 |
| (H-A) are
used to hold all cross stringers to side
stringers using a Washer Plate (H-W). The
wood is sandwiched between the steel and creates
a solid corner. $4.10 |
|
Backup Plates |
|
 |
 |
| (H-B) are
used with Single "T" Males (H-SM) and Single "T"
Females (H-SF) for additional strength and to
keep bolts from pulling through the wood.
$3.79 |
|
Cleat Angles |
|
 |
 |
| (H-CA)
have slots which accommodate various sizes of
cleats. The cleat angle is bolted to the
side stringer with a Washer Plate (H-W).
The cleat is then bolted through the deck into
the cleat angle. This arrangement keeps
the cleat from pulling out of the deck.
$5.80 |
|
Inside Corner - 3" I.D.
Pipe Holder |
|
 |
 |
| (H-IC3)
has a 3" I.D. pipe holder welded in place.
It can be used to replace a regular inside
corner. It will accommodate a 2" I.D.
pipe. $31.28 |
|
3" Pipe Holder |
|
 |
 |
| (P-3) can
bolt to the side stringer and uses 2" standard
pipe to anchor docks in place.
$18.72 |
|
Male/Female Outside Corner |
|
 |
 |
| (H-OCFM)
saves in using a Single "T" Male (H-SM) or
Single "T" Female (H-SF).
$30.12 |
|
Female/Female Outside
Corner |
|
 |
 |
| (H-OCFF)
saves in using Single "T" Females (H-SF).
$35.40 |
|
Male/Male Outside Corner
|
|
 |
 |
| (H-OCMM)
saves in using Single "T" Males (H-SM).
$25.01 |
|
Splice Plates |
|
 |
| (H-SP)
were designed to join two timbers together.
One is used on each side. Bolt placement
is such that an angle and 1 1/2" lumber can be
added at the splice and end up at the end of the
splice. Comes in set of two.
$33.87 |
|
Chain Retainers |
|
 |
 |
| (H-CR) Chain
Retainers bolt to the side of the dock and use
chain to hold a dock in place. Use chain
up to 1/2". Use two washer plates to
reinforce. $15.95 |
|
135 Degree Finger
Stabilizer |
|
 |
 |
| (H-135)
Using our H-135 hardware, you can easily
construct a finger stabilizer. Use H-SF or
H-SM to complete the job. Finger
stabilizers, especially on narrow fingers, tend
to spread the load on the main dock side
stringers. $15.17
To place an order, give us
a call at 1-800-290-5987 |
