Dock Hardware

Outside Corner End

Outside Corner End
Outside Corner End

(H-OCE) is used at the ends of fingers, ends of dock, or for a swim platform.

$14.19

Outside Corner Male

Outside Corner Male
Outside Corner Male

(H-OCM) has one 1/2″ tab and a hole for a 3/4″ bolt or pin. Use with an Outside Corner Female (H-OCF) or with a Single “T” Female (H-SF).
$20.47

Outside Corner Female

Outside Corner Female
Outside Corner Female

(H-OCF) has two 1/2″ tabs and a hole for a 3/4″ bolt or pin. Use with an Outside Corner Male (H-OCM) or with a Single “T” Male (H-SM).
$24.51

Inside Corner

Inside Corner
Inside Corner

(H-IC) has slots and can be used with 1 1/2″ – 3″ thick wood. The inside corner sandwiches the wood between the opposite outside corner, keeping bolts from burying themselves in the wood. A corner gusset gives the unit a lot of strength and helps from racking the dock.
$15.12

Single “T” Male

Single T Male
Single T Male

(H-SM) has one 1/2″ tab and is used with an Outside Corner Female (H-OCF) or Single “T” Female.
$10.98

Single “T” Female

Single T Female
Single T Female

(H-SF) has two 1/2″ tabs and is used with an Outside Corner Male (H-OCM) or a Single “T” Male (H-SM). Both male and female singles can be bolted to the side of a dock to make finger attachments. They can also be bolted to seawalls to make ramps.
$15.37

Washer Plates

Washer Plate
Washer Plate

(H-W) are used mostly with Angles (H-A) and Cleat Angles (H-CA). The square hole in the plate keeps the carriage bolts from turning when the bolts are tightened.
$1.49

Angles

Angles
Angles

(H-A) are used to hold all cross stringers to side stringers using a Washer Plate (H-W). The wood is sandwiched between the steel and creates a solid corner.
$4.10

Backup Plates

Backup Plates
Backup Plates

(H-B) are used with Single “T” Males (H-SM) and Single “T” Females (H-SF) for additional strength and to keep bolts from pulling through the wood.
$3.79

Cleat Angles

Cleat Angles
Angles

(H-CA) have slots which accommodate various sizes of cleats. The cleat angle is bolted to the side stringer with a Washer Plate (H-W). The cleat is then bolted through the deck into the cleat angle. This arrangement keeps the cleat from pulling out of the deck.
$5.80

Inside Corner – 3″ I.D. Pipe Holder

Inside Corner
Inside Corner

(H-IC3) has a 3″ I.D. pipe holder welded in place. It can be used to replace a regular inside corner. It will accommodate a 2″ I.D. pipe.
$31.28

3″ Pipe Holder

Pipe Holder
Pipe Holder

(P-3) can bolt to the side stringer and uses 2″ standard pipe to anchor docks in place.
$18.72

Male/Female Outside Corner

Male/Female Outside Corner
Male/Female Outside Corner

(H-OCFM) saves in using a Single “T” Male (H-SM) or Single “T” Female (H-SF).
$30.12

Female/Female Outside Corner

Female/Female Outside Corner
Female/Female Outside Corner

(H-OCFF) saves in using Single “T” Females (H-SF).
$35.40

Male/Male Outside Corner

Male/Male Outside Corner
Male/Male Outside Corner

(H-OCMM) saves in using Single “T” Males (H-SM).
$25.01

Splice Plates

Splice Plates

(H-SP) were designed to join two timbers together. One is used on each side. Bolt placement is such that an angle and 1 1/2″ lumber can be added at the splice and end up at the end of the splice. Comes in set of two.
$33.87

Chain Retainers

Chain Retainers
Chain Retainers

(H-CR) Chain Retainers bolt to the side of the dock and use chain to hold a dock in place. Use chain up to 1/2″. Use two washer plates to reinforce.
$15.95

135 Degree Finger Stabilizer

135 Degree Finger Stabilizer
135 Degree Finger Stabilizer

(H-135) Using our H-135 hardware, you can easily construct a finger stabilizer. Use H-SF or H-SM to complete the job. Finger stabilizers, especially on narrow fingers, tend to spread the load on the main dock side stringers.
$15.17